RUTX11 è un dispositivo molto potente dotato di Dual-SIM con failover automatico, WAN di backup e altre funzionalità SW. Una vasta gamma di interfacce hardware interne consente a questo prodotto di essere utilizzato in applicazioni industriali ad alto consumo di energia in cui la velocità e la robustezza sono al centro della soluzione. 4G LTE - Cat 6 DL fino a 300 Mbps in sincronia con 4 porte Ethernet da 1 Gbit consente un'esperienza di trasferimento dati senza interruzioni con failover automatico e una WAN di backup. Bluetooth LE consente di collegare i sensori direttamente al router, riducendo così al minimo l'ecosistema complessivo della soluzione.
Mobile
- Mobile module 4G (LTE) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps
- SIM switch 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail
- Status Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID
- SMS SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply
- Black/White List Operator black/white list
- USSD Supports sending and reading Unstructured Supplementary Service Data messages
- Band Managment Band lock, Used band status display
- APN Auto APN
- Bridge Direct connection (bridge) between mobile ISP and device on LAN
Wireless
- Wireless Mode 802.11b/g/n/ac Wave 2 (WiFi 5) with data transmission rates up to 867 Mbps (Dual Band, MU-MIMO), 802.11r fast transition, Access Point (AP), Station (STA)
- Wi-Fi Security WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation
- ESSID ESSID stealth mode
- Wi-Fi Users Up to 150 simultaneous connections
- Wireless Hotspot Captive portal (Hotspot), internal/external Radius server, built in customizable landing page
Ethernet
- WAN 1 x WAN port (can be configured as LAN) 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover
- LAN 3 x LAN ports, 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover
Network
- Routing Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP)
- Network protocols TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP, MQTT, Wake on LAN (WOL)
- VoIP passthrough support H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
- Connection Monitoring Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
- Firewall Port forwards, traffic rules, custom rules
- DHCP Static and dynamic IP allocation, DHCP Relay, Relayd
- QoS Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
- DDNS Supported >25 service providers, others can be configured manually
- Load Balancing Balance Internet traffic over multiple WAN connections